RH924UQ 标准200系列底板

描述

RH924UQ 标准200系列底板

标准200系列底板为DINrail安装的200系列模块提供安装平台和通信背板。

概述
这些标准的200系列底板支持小型和大型系统的分布式控制，并特别支持以下Foxboro Evo™系统模块:

现场控制处理器280 (FCP280)容错或非容错
现场设备控制器280 (FDC280)容错或非容错
现场控制处理器270 (FCP270)容错或非容错
现场通信模块(FCM100Et和fcm100e)和其他fcm
现场总线扩展模块(FEM100E)
现场总线隔离器/滤波模块(FBI200/FBI100)
标准现场总线模块(fbm)和100系列fbm连接。

支持标准fbm的200系列基板通过提供2、4和8个fbm位置的单位增量，结合垂直和水平安装，实现了整体系统安装功能。

特性
200系列底板的主要特点是:
对于支持fbm的底板:
•2、4和8个模块位置与垂直和水平安装相结合
•用于I/O终止组件的现场连接，每个模块的冗余适配器和模块标识符
•拨码开关，用于识别某些模块底板
•添加额外的200系列基板，而无需将系统从服务中移除(需要冗余总线)适用于FCP280/FCP270, FDC280和
FCM100Etbaseplates支持:
•连接可选的GPS时间频闪。所有非fdc280模块都需要分频器/终止器进行时间频闪连接。FDC280底板支持直连。除FDC280底板(RH101KF)外的所有底板

支持:
•连接到标准现场总线模块的2 Mbps模块现场总线，或连接到100系列fbm的268 Kbps现场总线
•用于A/B现场总线的分路器/终止器
•与现有的I/ o子系统向后兼容，允许未来扩展，无需额外的接口硬件主要和次要24 V直流电源和通信连接专用于单个cp型模块的关键位置，如FCP280, FDC280，或fcm /FBM，取决于底板类型无源背板，以提高系统可靠性

RH924UQ

RH924UQ 标准200系列底板

The Standard 200 Series baseplates provide the mounting platform and communication backplane for DINrail mounted 200 Series modules.

OVERVIEW
These standard 200 Series baseplates supportdistributed control for both small and large systemsand specifically support the following Foxboro Evo™system modules:

 Field Control Processor 280 (FCP280) faulttolerant or non-fault-tolerant
 Field Device Controller 280 (FDC280) faulttolerant or non-fault-tolerant
 Field Control Processor 270 (FCP270) faulttolerant or non-fault-tolerant
Field Communications Modules (FCM100Et andFCM100E) and other FCMs
 Fieldbus Expansion Modules (FEM100E)
 Fieldbus Isolator/Filter Modules (FBI200/FBI100)
 Standard Fieldbus Modules (FBMs) and100 Series FBMs connection.

The standard FBM-supporting 200 Series baseplatesenable overall system installation functionality byproviding unit increments of 2, 4, and 8 FBMpositions in combination with vertical and horizontalmounting.

FEATURES
Key features of the 200 Series baseplates are:
 For FBM-supporting baseplates:
• 2, 4, and 8 module positions in combinationwith vertical and horizontal mounting
• Field connection for I/O terminationassemblies, redundant adapters and moduleidentifiers for each module
• DIP switch for identification of certainModular Baseplates
• Adding additional 200 Series baseplateswithout removing the system from service(requires redundant bus) For FCP280/FCP270, FDC280, and
FCM100Etbaseplates support:
• Connection for optional GPS time strobe.All non-FDC280 modules requiresplitters/terminators for time strobeconnections. FDC280 baseplates supportdirect connection. All baseplates except the FDC280 baseplate(RH101KF)

support:
• Connection to the 2 Mbps Module Fieldbusfor the Standard Fieldbus Modules, or to a268 Kbps Fieldbus for the 100 Series FBMs
• Splitters/terminators for A/B Fieldbus
• Backwards compatibility with existing I/Osubsystems allowing for future expansionwithout additional interface hardware Primary and secondary 24 V dc power andcommunications connections Keyed positions dedicated to individual CP-typemodules such as the FCP280, FDC280, orFCM/FBM only, depending on the baseplate type Passive backplane to increase system reliability