XV-440-10TVB-1-13-1 处理方法包括使用工业显示器本身所带的色彩功能设置调整色彩设置

描述

XV-440-10TVB-1-13-1 处理方法包括使用工业显示器本身所带的色彩功能设置调整色彩设置

XV-440-10TVB-1-13-1 工业显示屏模块常见故障及其处理方法如下：

显示区域出现偏色或光斑：这可能是由于工业显示器所在环境存在较大的交变磁场，导致显示器磁化。处理方法包括查找附近是否存在大功率电器如大功率变压器、音箱等设备，并将其移开，使用工业显示器本身所带的消磁功能进行消磁，改变工业显示器摆放的方向以减少地磁对其的影响。

全部区域显示偏色：这可能是由于显示器的颜色设置出现偏差或显示卡的色彩设置出现偏差。处理方法包括使用工业显示器本身所带的色彩功能设置调整色彩设置，调整显示卡的色彩设置。

无显示：这可能是由多种原因引起的，包括工业显示器电路故障、工业主机故障、工业显示器的电源输入故障、工业显示器信号线和主机显示卡接触不良等。处理方法包括检查并更换损坏的部件，确保信号线插头与显示卡相固定，保证完全接触到位。

此外，XV-440-10TVB-1-13-1还有一些其他故障和处理方法：

部分区域出现偏色或光斑：这可能是由于工业显示器部分区域出现偏色或光斑。处理方法包括查找附近是否存在大功率电器如大功率变压器、音箱等设备，并将其移开，使用工业显示器本身所带的消磁功能进行消磁，改变工业显示器摆放的方向以减少地磁对其的影响。

花屏：这可能是由于系统下不显示或花屏。处理方法包括更换显示器确认显示器是否正常，更换显示器线材是否正常，确认机器是否有显卡，同时显示器是否连接到显卡上；若在显卡上，首先尝试更换显示接口，仍不显示或花屏，尝试更换显卡驱动；确认机器无显卡，同时开机后为双显，但只有一个显示，确认系统驱动正常后，检查显示模式是否有被断开导致，设置成扩展或克隆显示，在确认显示是否正常。

网络异常：这可能是由于网络故障引起的。处理方法包括检查连接网线是否正常、网络接口内弹针是否正常、确认网络IP是否有被固定、固定IP与实际所在局域网IP区间内、使用CMDping命令 ping局域网内网关IP、确认是否可以ping通、查看网络灯状态是否正常、网络连接是否被禁用等。

XV-440-10TVB-1-13-1 处理方法包括使用工业显示器本身所带的色彩功能设置调整色彩设置

XV-440-10TVB-1-13-1 Common faults of industrial display modules and their solutions are as follows:

Color bias or light spots in the display area: this may be due to the presence of a large alternating magnetic field in the environment of the industrial display, resulting in the magnetization of the display. Processing methods include finding whether there is a nearby high-power electrical appliances such as high-power transformers, speakers and other equipment, and move it away, using the industrial display itself with the degaussing function for degaussing, change the direction of the industrial display to reduce the impact of geomagnetic.

All areas display color bias: This may be due to a deviation in the color Settings of the display or a deviation in the color Settings of the display card. The processing method includes using the color function Settings of the industrial display itself to adjust the color Settings and adjust the color Settings of the display card.

No display: This may be caused by a variety of reasons, including industrial display circuit failure, industrial host failure, industrial display power input failure, industrial display signal line and poor contact with the host display card. The treatment method includes checking and replacing the damaged parts, ensuring that the signal cable plug is fixed with the display card, and ensuring that the contact is fully in place.

In addition, XV-440-10TVB-1-13-1 has some other faults and handling methods:

Partial color or light spots: This may be due to partial color or light spots in some areas of industrial displays. Processing methods include finding whether there is a nearby high-power electrical appliances such as high-power transformers, speakers and other equipment, and move it away, using the industrial display itself with the degaussing function for degaussing, change the direction of the industrial display to reduce the impact of geomagnetic.

Flower screen: This may be due to the system does not display or flower screen. The processing methods include replacing the monitor to confirm whether the monitor is normal, replacing the monitor wire is normal, confirming whether the machine has a graphics card, and whether the monitor is connected to the graphics card; If on the graphics card, first try to replace the display interface, still do not display or spend the screen, try to replace the graphics card driver; Confirm that the machine has no graphics card, and there is dual display after starting up, but only one display. After confirming that the system driver is normal, check whether the display mode is disconnected, and set it to extended or clone display, and confirm whether the display is normal.

Network exception: This may be caused by a network fault. Troubleshooting methods include checking whether the network cable is normal, whether the pins in the network interface are normal, whether the network IP address is fixed, whether the fixed IP address is within the IP address range of the actual LAN, using the CMDping command to ping the gateway IP address of the LAN, whether the network indicator is normal, and whether the network connection is disabled.