EL6695 可以用于CAN总线数据收发

倍福(Beckhoff)的EL6695模块是一款电池管理芯片,具有精确的电池电流和电压控制能力,支持多种类型的电池,如锂电池、铅酸电池和镍氢电池等。此外,它还可以用于CAN总线数据收发,将CAN数据信号转化为RS232串口信号。

分类:
  • 购买咨询热线/Phone:18859254943
  • 邮箱/Email:sales@ygdcs.com
  • 地址:成都高新区天益街北巷52号附14号2层

描述

EL6695 可以用于CAN总线数据收发

倍福(Beckhoff)的EL6695模块是一款电池管理芯片,具有精确的电池电流和电压控制能力,支持多种类型的电池,如锂电池、铅酸电池和镍氢电池等。此外,它还可以用于CAN总线数据收发,将CAN数据信号转化为RS232串口信号。

EL6695模块的具体参数和特点可能因不同的产品系列和应用场景而有所差异。一般来说,使用EL6695模块需要遵循以下步骤:

了解模块的硬件接口和支持的波特率等参数。
进行模块参数配置,包括波特率、工作模式等,可以通过串口终端软件或其他专业工具进行配置。
验证配置结果,通过相应的硬件设备进行测试,确保数据收发正常。
如果测试结果不符合预期,可以通过调整配置参数进行修改,直到达到理想状态。
需要注意的是,在使用EL6695模块时,需要遵守相关的安全规范和操作指南,确保设备的正常运行和人身安全。此外,还需要根据实际应用场景和需求进行综合考虑,选择合适的模块和配置方式,以实现最佳的性能和效果。

 

倍福(Beckhoff)的EL6695是一款EtherCAT桥接端子模块,具有以下具体参数和特点:

  1. 接口与连接
  • 初级侧:E-bus(终端线束)
  • 次级侧:2 x 100 Mbit/s以太网,RJ45,输入/输出端口
  1. 功能
  • EtherCAT分布式时钟同步
  • 数据交换
  1. 电缆长度:100m,100BASE-TX
  2. 电源
  • 初级侧通过E总线供电
  • 次级侧通过连接器供电,电压为24V
  1. 电气隔离:500V(E-bus / 次级侧)
  2. 电流消耗
  • E-bus:400mA
  • 次级侧:70mA / 24V
  1. 过程映像中的位宽大值:每个方向3千字节(取决于EtherCAT主站,TwinCAT当前大1400字节)
  2. 特殊功能
  • 在TwinCAT中可用作参考时钟
  • 支持同步数据交换
  • 灵活的PDO映射
  • 支持AoE, EoE, FoE, VoE等异步通信
  1. 物理特性
  • 重量:约85克
  • 工作/存储温度:0°C … +55°C / -25°C … +85°C
  • 相对湿度:95%(无冷凝)
  • 抗振动/抗冲击性:符合EN 60068-2-6 / EN 60068-2-27
  • EMC抗扰度/发射:符合EN 61000-6-2 / EN 61000-6-4
  • 认证:CE, UL
  • 安装位置/保护等级:IP 20

请注意,这些参数可能会因产品升级或改进而发生变化。因此,在选择和使用EL6695时,建议参考最新的产品手册、技术文档或联系倍福公司以获取最准确和最新的信息。此外,还需要根据实际应用场景和需求进行综合考虑,以确保设备的正确选择和使用。

EL6695 可以用于CAN总线数据收发

The Beckhoff EL6695 module is a battery management chip with precise battery current and voltage control that supports a wide range of battery types such as lithium, lead-acid and nickel-metal hydride batteries. In addition, it CAN also be used for CAN bus data transceiver, CAN data signal into RS232 serial signal.

The specific parameters and characteristics of the EL6695 module may vary according to different product families and application scenarios. In general, to use the EL6695 module you need to follow the following steps:

Understand the hardware interface of the module and the parameters such as the supported baud rate.
You can configure module parameters, such as baud rate and working mode, by using serial port terminal software or other professional tools.
Verify the configuration results, and test the corresponding hardware devices to ensure that data is properly sent and received.
If the test result does not meet expectations, it can be modified by adjusting the configuration parameters until the ideal state is reached.
When using the EL6695 module, you must comply with the relevant safety regulations and operation guidelines to ensure the normal running of the device and personal safety. In addition, it is also necessary to comprehensively consider the actual application scenarios and requirements, and select the appropriate module and configuration mode to achieve the best performance and effect.

 

The Beckhoff EL6695 is an EtherCAT bridge terminal module with the following specific parameters and features:

Interfaces and connections:
Primary side: E-bus (Terminal harness)
Secondary side: 2 x 100 Mbit/s Ethernet, RJ45, input/output port
Features:
EtherCAT Distributed clock synchronization
Data exchange
Cable length: 100m, 100BASE-TX
Power Supply:
The primary side is powered by the E bus
The secondary side is powered by a connector with a voltage of 24V
Electrical isolation: 500V (E-bus/secondary side)
Current consumption:
E-bus: 400mA
Secondary side: 70mA / 24V
Bit width in the process image: 3 kilobytes per direction (depending on EtherCAT master, TwinCAT is currently 1400 bytes larger)
Special Features:
Can be used as a reference clock in TwinCAT
Supports synchronous data exchange
Flexible PDO mapping
Support AoE, EoE, FoE, VoE and other asynchronous communication
Physical characteristics:
Weight: About 85 grams
Operating/storage temperature: 0°C… +55°C / -25°C … +85°C
Relative humidity: 95% (non-condensing)
Vibration/impact resistance: according to EN 60068-2-6 / EN 60068-2-27
EMC immunity/emission: compliant with EN 61000-6-2 / EN 61000-6-4
Certification: CE, UL
Installation position/Protection level: IP 20
Please note that these parameters may change due to product upgrades or improvements. Therefore, when selecting and using EL6695, it is recommended to refer to the latest product manuals, technical documentation or contact Beckhoff for the most accurate and up-to-date information. In addition, comprehensive considerations must be made based on actual application scenarios and requirements to ensure the correct selection and use of the device.

 

DSPC172 57310001-ML ABB处理器板 INSEM01事件序列贝利大师
Dsdx404 57160001- I/O单元abb PM630 3BSE000434R1处理器模块ABB
DSPC170 57310001-GL mp200处理器模块ABB PM632 3BSE005831R1处理器单元ABB
DO630 3BHT300007R1 ABB数字输出16Ch 250VAC隔离 IC693CPU372 GE TCP I/P以太网通信接口
Dsqc202 yb560103-ac /5基极连接abb IC697PWR748 GE机架式电源模块
DSQC313 3HAB2213-1/2串行测量模块ABB IC693CPU372-AE GE TCP I/P以太网通信接口
DSQC322 3HAB5960-1 I/O单元ABB DeltaV™s系列传统I/O EMERSON
DSQC352 3HNE00009-1输入输出单元ABB mcmr Prosoft Modbus通信模块
Dsqc354底座连接abb MVI69-MNET ProSoft Modbus TCP/IP通信模块
DSQC602 3HAC12816-1/07 ABB机器人公司卡 PLX31-MBTCP-MBS4 ProSoft Modbus TCP/IP到Modbus串口网关
3HAC12934-1 ABB客户I/O PS DSQC608 MVI69-MCM ProSoft Modbus网络接口模块
DSQC609 3HAC14178-1 ABB电源 MVI56E-MCMR-CC Prosoft ControlLogix增强Modbus
DSQC627 3HAC020466-001 ABB电源 MVI94-MCM ProSoft Modbus主/从网络接口模块
DSTD108 57160001-ABD ABB连接单元,用于8通道24-250 VAC MVI56E-MNETC-CC ProSoft Modbus TCP/IP多客户端/服务器增强网络接口模块
EHDB130 ABB传动接触器 330703-000-060-10-02-00
269PLUS-D/O-100P-125V GE数字电机继电器装置 VE4005S2B1德尔塔V标准I/O终端块
IMMFP12多功能处理器模块 330730-080-00-00 3300 XL 11mm加长电缆Bently Nevada

 

 

  • 购买咨询热线/Phone:18859254943
  • 邮箱/Email:sales@ygdcs.com
  • 地址:成都高新区天益街北巷52号附14号2层